Mopar Muscle Association UK

when it comes to window regulators there will be commonality with 66 67 68 US cars i would suspect yours is a VIP so the oddness on your car is slightly longer rear doors i.e the fronts should have internals much like a late 60s 4 door US model and of course the one that is worn out on yours is pass...

slightly less £££ than webcon. and here is something that you probably should avoid https://www.aliexpress.com/item/4001174196533.html?src=google&src=google&albch=shopping&acnt=494-037-6276&slnk=&plac=&mtctp=&albbt=Google_7_shopping&albagn=888888&isSmbAutoCall=fal...

https://www.webcon.co.uk/products/613-14031404-calibration-kit/ dunno if the kit is right look at the cost!!! Magnetti Marelli/LCN in spain who make the official weber carbs also make the current edelbrock carbs you will find a weber logo on there somewhere for 500 and 600 CFM carbs find a rover v8 ...

dancing party shawaddy waddy..

i was 6



Dave

id have this if it was £6K and put it right, sell the ford stuff, and put back a Mopar Drive train to fit that engine and box i think they will have hacked out the middle of the torsion bar cross member. so would need a new one of them fitted and it would be worth about £20K-£30K to an Australian in...

fantastic

lottery win to afford it mind £62K

Dave

that's going to feel nice a solid and planted next time its driven..... It great when you get something done and you can feel the positive impact as soon as you drive it. it will be like vanishing point without the drugs and naked cycling on the drive home... just be careful if there are road works ...

keep that a whack a mustang t5 in it ...:) get the v6 one with the truck like 1st and a 0.73 Overdrive or the AX aisin warner that they used in the dodge trucks a bellhousing from 318 to the aisin warner exists makes it easier than the t5 https://www.novak-adapt.com/knowledge/transmissions/manual/ax...

the washers may be the correct way round for the year of the car and the rubber that was fitted if you look across a range of manuals you will find that chrysler changed their mind about 50,000 times over the 60s and 70s across early and late A and B bodies the age of the car would normally have had...

the spigot problem can be overcome depending on how short or long your input shaft is too short too small sleeve the end to 0.750 and run a dodge dakota roller spigot in the hub of the crank that usually accommodates the front of the converter too long and you may have to chop off some of the end ,a...

Nice one stu.. try before you buy....
just keep saving copies so you can go back to the last good one after a disaster

i have a vision of you swearing at the PC at 3:30 am



Dave

when you replace the crank its an aftermarket part, it probably assumes internally balanced assembly if you replace the rods....and i think you are gonna have to, you will need to get it all balanced up anyway to use standard rods you would have to get some pistons with the pin really quite high wit...

360 like 318 but bigger capacity, different sized journals and externally balanced in standard cast crank form change crank and rods and balancer and torque converter (or remove weights) if manual you may have to make sure the crank has the spigot for the input shaft most were truck application so w...

might be worth rigging up some vacuum advance. that will help stop the plugs getting grubby at idle 45* under no load is perfect :) with 15 initial to allow it to start. i never bothered with it until i got some bits recently for mine. vacuum can that worked and one of these https://www.gsparkplug.c...

a long time ago (2003) in a galaxy far far away i drove west from Sydney down the parramatta road and got lost in suburbia land... i met a man who sold me an aircon/heater unit and the heavy weight metal and plastic vent/diffuser for a H51 RHD car he also sold me a screen and some other gubbins a lo...