dart info
Moderator: Moderators
Re: dart info
Murphy's law. Will try again.
Re: dart info
Hi Pete, gave up on the PM. Looking any background info on the Dart 340 engine. Who built it, has it been rebored, sure it has a aftermarket cam. Issue is, I can hear a knock on start up. Not all the time, but enough to worry me. Once oil pressure goes above 20PSI it has gone and she drives great. Will know more next weekend when I take her down to Ian's place. But Ian is a Chevy man, doesn't really like working on mopar engines. I think you owned her at one time. Originally a 383. Has an extra set of spring perches 3 inches in from the origionals. I believe she was raced at one time. Just want to know if anyone has any info on it before we tear it down. Hope all's well.
Re: dart info
Sorry, I do not have any background info on it.
Jim Wilson may know more.
Is the noise top end or bottom end on start up?
Jim Wilson may know more.
Is the noise top end or bottom end on start up?
Pete Wiseman; Cambridge.
Mopar by the grace of God
Mopar by the grace of God
Re: dart info
Bottom end Pete. sorry had that on the PM.
Re: dart info
Oil changed last year. Valvoline VR1 20/50. Looks clean to me. thanks for replying, possibly selling her later in the year, but wouldn't do it to a member without her being right. heading down to the garage now. May be a job for DaveB, Everything else is looking great except for the engine. Does need a clean up at the least.All best, Gerry
Re: dart info
Do you have a mechanical oil pressure gauge on the car?
If not, it may be worth temporarily installing one on the back of the block and see what you get cranking / Fire up / idiling / fast idle.
It sounds like bearing wear to me, but it may be a (clutching at straws) sticking oil pressure relief valve...
If not, it may be worth temporarily installing one on the back of the block and see what you get cranking / Fire up / idiling / fast idle.
It sounds like bearing wear to me, but it may be a (clutching at straws) sticking oil pressure relief valve...
Pete Wiseman; Cambridge.
Mopar by the grace of God
Mopar by the grace of God
Re: dart info
Just an outside thought, my big end knock was a broken flex plate. I could actually see the crack once access cover removed from underneath.
May not be the case with yours, but worth a look. I only discovered it after I had the bottom end apart.
May not be the case with yours, but worth a look. I only discovered it after I had the bottom end apart.
Matt Hollingsworth - Vehicle Registrar
Panther Pink 73 Aussie Charger 265 Hemi 4 spd
Challenger Sam Posey Tribute car
Panther Pink 73 Aussie Charger 265 Hemi 4 spd
Challenger Sam Posey Tribute car
Re: dart info
I don't Pete. Above my capabil
ities. Job for my mate Ian. Leg end over here. Hope to get down next weekend. Still working on indicator not flashing. Anyone know wat this is and where I can get one ? Thanks for the advice, GerryRe: dart info
Gerry, if the flasher is buggering about, get an electronic one from MOSS.
They are cheaper now than when i fitted mine, and don't use bimetallic strips to break the current, just electronics so teh flash rate is always steady. They were £20 a go, now listed at £10.
https://www.moss-europe.co.uk/electroni ... units.html
Car Builder Solutions do them too, even cheaper. They are a great source for parts.
https://www.carbuilder.com/uk/3-pin-tra ... V8EALw_wcB
They are cheaper now than when i fitted mine, and don't use bimetallic strips to break the current, just electronics so teh flash rate is always steady. They were £20 a go, now listed at £10.
https://www.moss-europe.co.uk/electroni ... units.html
Car Builder Solutions do them too, even cheaper. They are a great source for parts.
https://www.carbuilder.com/uk/3-pin-tra ... V8EALw_wcB
Matt Hollingsworth - Vehicle Registrar
Panther Pink 73 Aussie Charger 265 Hemi 4 spd
Challenger Sam Posey Tribute car
Panther Pink 73 Aussie Charger 265 Hemi 4 spd
Challenger Sam Posey Tribute car
Re: dart info
Cheers Matt