Before I go butchering with a hacksaw, any tips on the best way / tools for cutting a plastic shifter housing to fit over the trans tunnel?
Seems very thick brittle plastic, but want to make a neat job of it.
Cutting shifter housing
Moderator: Moderators
- Stu
- Posts: 6886
- Joined: Sun Jul 31, 05 4:15 pm
- Location: Shropshire, home of the worlds smallest big screen TV
Cutting shifter housing
24 hours in a day, 24 beers in a case. Coincidence? I think not…
70 Challenger
MMA/489
NSS/435
70 Challenger
MMA/489
NSS/435
Re: Cutting shifter housing
I use a thin cutting disc and careful use of a grinding disc if it's a curve, slow and steady. I normally fit to the floor shape first and then shorten it afterwards if needed. That way if you cock up you've still got some material left to correct it.
“This ain’t no party, this ain’t no disco, this ain’t no foolin’ around”
- Stu
- Posts: 6886
- Joined: Sun Jul 31, 05 4:15 pm
- Location: Shropshire, home of the worlds smallest big screen TV
Re: Cutting shifter housing
Thanks Blue. Wasn’t sure if a cutting disc would splinter it, so good to know.
24 hours in a day, 24 beers in a case. Coincidence? I think not…
70 Challenger
MMA/489
NSS/435
70 Challenger
MMA/489
NSS/435
Re: Cutting shifter housing
No it won't, they crack very easily if a hacksaw blade suddenly jams though I can tell you that!
“This ain’t no party, this ain’t no disco, this ain’t no foolin’ around”
- Stu
- Posts: 6886
- Joined: Sun Jul 31, 05 4:15 pm
- Location: Shropshire, home of the worlds smallest big screen TV
Re: Cutting shifter housing
I wasn’t really going to hacksaw it, just checking.
Instructions with the shifter says tin snips, though... sounds like a recipe for disaster to me.
Instructions with the shifter says tin snips, though... sounds like a recipe for disaster to me.
24 hours in a day, 24 beers in a case. Coincidence? I think not…
70 Challenger
MMA/489
NSS/435
70 Challenger
MMA/489
NSS/435
Re: Cutting shifter housing
Yea, think I'd rather try biting chucks out of it than tin snips....
“This ain’t no party, this ain’t no disco, this ain’t no foolin’ around”
- Stu
- Posts: 6886
- Joined: Sun Jul 31, 05 4:15 pm
- Location: Shropshire, home of the worlds smallest big screen TV
Re: Cutting shifter housing
Planning to make a template from the tunnel and start low, as you suggest. I want to make a neat job of it, so rather take some time to get it right.
24 hours in a day, 24 beers in a case. Coincidence? I think not…
70 Challenger
MMA/489
NSS/435
70 Challenger
MMA/489
NSS/435
Re: Cutting shifter housing
Thin grinding discs are great for nearly everything these days, they work very well.
Matt Hollingsworth - Vehicle Registrar
Panther Pink 73 Aussie Charger 265 Hemi 4 spd
Challenger Sam Posey Tribute car
Panther Pink 73 Aussie Charger 265 Hemi 4 spd
Challenger Sam Posey Tribute car
- Stu
- Posts: 6886
- Joined: Sun Jul 31, 05 4:15 pm
- Location: Shropshire, home of the worlds smallest big screen TV
Re: Cutting shifter housing
Was planning on using a Dremel, but realised I picked up an oscillating one rather than a spinning one.
Hey ho. Out with the angle grinder and thin disc it is then.
Hey ho. Out with the angle grinder and thin disc it is then.
24 hours in a day, 24 beers in a case. Coincidence? I think not…
70 Challenger
MMA/489
NSS/435
70 Challenger
MMA/489
NSS/435