Half inch lift cam and stock rockers?

Pete · Post by **Pete** » Wed May 20, 20 6:14 pm

Refused to speak to me, had to get Geof Hauser to spec and order the Convertor....

Blue · Post by **Blue** » Wed May 20, 20 7:26 pm

I'm talking about Hughes the engine outfit, I don't think the converter firm are the same company?

RobTwin · Post by **RobTwin** » Thu May 21, 20 12:08 am

Blue wrote: ↑Wed May 20, 20 7:26 pm I'm talking about Hughes the engine outfit, I don't think the converter firm are the same company?

I did wonder that but thought they must be different

Dave-R · Post by **Dave-R** » Thu May 21, 20 11:16 am

Not the same company.

Mind you my mate Eddie Nasser didn't get far with Hughes Engines. I don't think they liked the surname.....

RobTwin · Post by **RobTwin** » Thu May 21, 20 11:54 am

Hughes Engines seem to get mixed reviews in the States as well...

https://dodgeforum.com/forum/central/30 ... e-off.html

kma176 · Post by **kma176** » Thu May 21, 20 10:52 pm

I found Hughes engines really helpful with plenty of info when I built mine.Lots of costings and different options for different applications .

Dave-R · Post by **Dave-R** » Fri May 22, 20 12:17 pm

Actually I just heard back from them last night and opened dialogue with me.

Watch this space as I try to cancel my Summit Order as it will not ship until the 3rd June.

Dave-R · Post by **Dave-R** » Fri May 22, 20 12:21 pm

Hughes 220/224 duration @ 0.050 cam with 0.503/0.518 lift is probably my best choice for what I am doing.

So I will see what I can sort out.

Blue · Post by **Blue** » Fri May 22, 20 12:41 pm

It might just be 'ol Dave running the show at the moment, I've heard a few smaller firms over there are struggling on single handed.

Dave-R · Post by **Dave-R** » Sat May 23, 20 10:51 am

His sons used to be OK. It's just Dave that is the grumpy old republican fart.

Anyway. Great service once they got going. Parts are due to arrive by the end of the week. My order was handled by someone called "Tim".

Dave-R · Post by **Dave-R** » Sat May 23, 20 10:54 am

So far I have only ported one intake on the heads. I am getting very lazy in my old age.
Doesn't seem to be much of a hurry though......

Pete · Post by **Pete** » Sat May 23, 20 11:07 am

I assume you bought a cam kit with lifters, timing set and springs?

Dave-R · Post by **Dave-R** » Mon May 25, 20 6:58 pm

Pete wrote: ↑Sat May 23, 20 11:07 am I assume you bought a cam kit with lifters, timing set and springs?

The timing set on the block is pretty new so keeping that. Yes on the lifters and springs.

Pete · Post by **Pete** » Mon May 25, 20 7:17 pm

John · Post by **John** » Mon May 25, 20 9:19 pm

Also be wary of hydraulic lifters these days Dave. I bought a Comp cam .510 lift kit and the lifters supplied were not up to the job. It took me ages and a lot of money before sussing it out and putting it right. They wouldn't rev past 5000rpm

Mopar Muscle Association UK

Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?

Re: Half inch lift cam and stock rockers?