a bit of this and a bit of that

It's not Mopar, but we like it

Moderator: Moderators

mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

phew! that was close..... i nearly had to buy a mk2 consul gasser this morning. luckily it sold for more than i was willing to bid. it was the old 'high on gas' car from the ashford kent area (invicta roadsters car?) so some may remember it?
neil.
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

back onto the monza axle today, we cut all of the factory 5 link brackets off and cleaned up the axle tubes. now it's ready for the caliper, 'new' 5 link and coilover brackets. :thumbright:
neil.
Attachments
IMG_0004 - Copy (17).JPG
IMG_0004 - Copy (17).JPG (98.84 KiB) Viewed 1817 times
IMG_0005 - Copy (10).JPG
IMG_0005 - Copy (10).JPG (132.04 KiB) Viewed 1817 times
IMG_0006 - Copy (9).JPG
IMG_0006 - Copy (9).JPG (104.26 KiB) Viewed 1817 times
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

today we made the caliper brackets for the opel monza axle. first a cad template was cut. then transferred to 12mm steel plate along with a pair of flitch plates to stiffen them more. with these all cut we tacked them in place. all we need to do now is fully weld them. the flitch plates were added as it's tight to get to the backside of the brackets for welding. so the best solution was to add the bracing for belt 'and' braces support. the bleed nipples are swapped to the flexi holes in the caliper so that they are now at the highest point for bleeding. :thumbright:
neil.
Attachments
IMG_0002 - Copy (28).JPG
IMG_0002 - Copy (28).JPG (98.46 KiB) Viewed 1714 times
IMG_0003 - Copy (24).JPG
IMG_0003 - Copy (24).JPG (105.93 KiB) Viewed 1714 times
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

well the brackets are now welded on for good along with the flitch plates. :thumbright:
neil
Attachments
IMG_0004 - Copy (18).JPG
IMG_0004 - Copy (18).JPG (96.66 KiB) Viewed 1637 times
User avatar
mopar_mark
Posts: 6752
Joined: Fri Jul 14, 06 8:01 pm
Location: Windlesham, Surrey

Re: a bit of this and a bit of that

Post by mopar_mark »

Those brackets look nice & solid, great work 👍🏼👍🏼👍🏼
"I spent a lot of money on booze, birds and fast cars. The rest I just squandered."
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

mopar_mark wrote: Sat Oct 17, 26 6:16 pm Those brackets look nice & solid, great work 👍🏼👍🏼👍🏼
thenks, they're a bit belt and braces but better too strong than not strong enough. it's brakes after all so..... :thumbright:
neil.
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

as if we've not got much to do there's a set of jag driveshafts and wishbones arriving saturday to be narrowed.🙄
neil.
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

when i get back to my nash i'm going to upgrade the speedway front brakes. i've just bought a pair of the imprezza wrx sti 4 pot calipers, same as the ones i used on the wolseley front axle seen here a while ago. those calipers along with a bigger pair of discs will be just fine.
neil.
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

i've just paid for the most expensive pair of rocker covers i've ever bought! but.... they're M/T finned ally ones for a ford fe big block so the odds were against me of finding a bargain. i could've got 2 pairs of new cheapy chrome ones for the same money but i din't want chrome ones, i gave our ashley the chrome edelbrock ones i had so.... basically like most of us i want what i want and often have to take a deep breath and just pay up.
neil.
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

we've been a bit quiet as we're doing one of those 'family and friends' jobs. this one's just inner and outer sills on a 2000/1 fiesta (for a mate at rally design) so not photo worthy.
normal programming will be resumed later this week, lol.
neil.
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

the fiesta's done ready to go tomorrow. we ran out of wire halfway though the job and i'd decided to try 1mm instead of the 0.8mm we've always used in this welder (the feed roller has 0.6 and 0.8 'grooves'). the 1mm wire is cheaper anyway so.... i also ordered 1.2mm tips for the torch as scott used to say go next size up on the tips as the wire's less likely to 'stick' if there's more room. 
so the result is after tweaking the wire speed : voltage settings it welds much nicer with the thicker wire and running it through the 0.8 roller works just fine.
​​​​​​​neil.
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

so to go with the luverly m/t valve covers (see above) i just ordered a pair of edelbrock ally heads for for my 390 from summit. they'll help with both weight and performance :thumbright:
neil.
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

i just ordered the gaz coilovers for the wolseley, they'll be dropped off after work today. :thumbright:
​​​​​​​neil.
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

ok, so remember the viva magnum rear disc conversion we did a while ago? tony was happy but......it meant the front discs were now much smaller than the rears. the obvious fix of course is to do a big disc/caliper conversion for the front. so after much research we decided on peugeot 406 vented front discs. these are the same 'offset' as the stock tiddly discs so 'just' needed altering to fit the viva hub. the centre bore is about 3/16" bigger so firstly we ran a bead of weld around the inside edge and then turned this to size on the lathe. next we drilled the viva hub pcd between the existing bolt holes. then the mounting part of the viva discs are about twice the thickness of the peugeot ones. this was a simple fix, we turned the friction part of the viva disc off of the centre so the centre could be used as a spacer which doubles up as a load spreader too (win win). lastly we chased the threads on the hub and cut new decent allen bolts to length as the old bolts were rusted beyond reuse.
next the hub will be refitted and the subaru 4 pot calipers will be mocked in place so new brackets can be made.
here's a couple of pics to show how tiny the old discs were and the old discs centre in place behind the new disc, all bolted to the viva hub.
neil.
Attachments
IMG_0005 - Copy (11).JPG
IMG_0005 - Copy (11).JPG (115.25 KiB) Viewed 419 times
IMG_0006 - Copy (10).JPG
IMG_0006 - Copy (10).JPG (102.32 KiB) Viewed 419 times
mygasser
Posts: 1696
Joined: Tue Dec 19, 17 10:36 am
Location: faversham, kent

Re: a bit of this and a bit of that

Post by mygasser »

wow, that was fast! the first head from summit racing arrived this morning.... only 3 days from ordering. postie said the second one should be tomorrow. :thumbright:
​​​​​​​neil.
Post Reply