Propshaft UJ replacement

Moderator: Moderators

Post Reply
User avatar
Steve
Posts: 7726
Joined: Wed Feb 01, 12 7:19 pm
Location: Scotland

Propshaft UJ replacement

Post by Steve »

Afternoon all,

Going to replace the UJs on my Polara soon. It's not a job I have done before but have watched numerous detailed videos so feel prepared to have a go.

Was wondering if there are any recommended 'dos and donts' from experience?? Anything else I should do as a matter of course when the prop shaft is off (I've ordered an output seal for the 727 if needed).

I plan on refreshing and painting stuff while it's off with POR15. I will also mark the position of everything relative to everything else but not sure if this is necessary when replacing the UJs?

Thanks in advance for any advice,

Cheers Steve :thumbright:
Bat Girl Stalker Living Petes Dream
User avatar
Steve
Posts: 7726
Joined: Wed Feb 01, 12 7:19 pm
Location: Scotland

Re: Propshaft UJ replacement

Post by Steve »

I'm now thinking that the whole propshaft assembly is balanced as one component so regardless of what I'm doing, I should mark everything to be safe..... A plan is developing :read2:
Bat Girl Stalker Living Petes Dream
User avatar
Dave999
Posts: 9624
Joined: Thu Feb 24, 05 10:31 am
Location: Twickenham,London, England

Re: Propshaft UJ replacement

Post by Dave999 »

Here we go
things i have found out by some trial and a lot of error over the last 25 years :)


don't drop the tiny bolts that hold the straps around the joint, at the yoke on the pinon shaft, into the gravel, or into the interior of your overalls so you can fire them out of a trouser leg into the gravel.........
make sure you have the correct joints small dodge or large dodge slang terms that will find you the correct names and part numbers in google
a C body might be a "Large dodge" jointed car if its got a big motor.
if ite been messed with had a diff swap etc it may have big at one end and a big to small conversion joint at the other.....beware
small (7260) and large (7290) Dodge U-joints

Mopar used what are termed internal C clip joints the clip sits inside the ears of the yoke and fit a groove on the cup
other brands used spring clips more like piston pin clips in the outer end of the hole in the ear that act on the end of the cup.

make sure you have a decent selection of tiny sockets and extensions and some open ended spanners to undo the little bolts that hold the straps
make sure you can turn the shaft, trans- N, and rear lifted no hand brake.
As soon as you jack up the rear end of the car , the suspensions goes to full droop the pinion angle changes meaning 2 out of the 4 nuts will have access restircted by the prop shaft.

the joint will be a tight fit into the yoke at the rear and will take a bit of WORK to get it out
you will have 1-4/-3/4 inch, to play with, to shove the lot forward, the front yoke into the trans further in order to get the shaft off the yoke at the back.

at the front as soon as you take the yoke out of the transmission, the oil/trans fluid will flow out of your trans with some uregncy.... kinda obvious but easy to forget :) simiar to speedo cable drive change....

i have in the past used a nice clean bucket to collect it and put it back in... can't over fill if just putting back what came out.
varrious bottle tops and deorderant tops can be slipped into the seal avoid this but you need to find one that fits when the trans is out and dry and store it for future use.
or find a "Rebuilt Manual Trans" rubber plug, that fits the spline of the output shaft and has an OD of that of the seal. hard to come by as, they are designed to be pushed into the trans by the first application of the yoke and just live in there forever. These let the OEM or rebuilder ship the trans full of oil

The way to avoid this is to ping off the clips on the trans yoke cups pull the shaft and joint, and leave the yoke in place...

but then the fun starts
you have to get the new joints onto the prop shaft and then to fit you need to get the other four cups into their places on both Yokes on the car
not as easy as you would think.

the cups are grease filled and have a hard ish rubber skirt/seal. To seat them where they would sit in normal operation you need to overcome some pressure from the seal and Air/grease in the cup. they are not going to squish in easily by hand.
getting them both compressed in so you can add the clips is more awkward under the car. it can be done but its easier with a nice big vice and a couple of small sockets just to gently hold the lot in place while you tap in the clips.
its worth compressing the pair that will fit the rear yoke now, so at least you have a fighting change of getting it in with the clips in place when back under the car.

depends if you presfer working upright with a bucket full of trans fluid to put back, OR you are happy to work under the car

if you have a 4 post lift and a selection of G clamps or similar under the car would be fine

bolt it back up
you will have to tap the joint into the rear yoke
tap it to center it in the yoke to aim the C clips into the right place. to centre it. rotate cups so the action of tapping/pushing the cross of the joint into the yoke dose not push off the clips back of the "C" of the c clip into the "C" shape of the yoke on the pinion shaft
put the straps on finger tight and just check its properly seated and then do them up to specified torque
if its in right you should be able to turn the shaft and see all 4 cups properly seated no gaps, should look like its been there for years apart from its shiny..... one side sticking out....you have mashed the C clip or its off its groove and is sitting on the seal i.e you did more than tap it into place ....

if you have some fancy pants yoke that uses U bolts and nulock nuts don't do them up so tight as to crush the cups...
I think standard setup used steel straps and small bolts

those C clips are hard springy steel BUT not that springy you can snap them..... they are closer to piston ring , than throttle spring, material
New is best, but haveing a box of get out of jail free, old decent ones is handy just in case

used joints are easier to fit back up

dave
The Greater Knapweed near the Mugwort by the Buckthorn tree is dying
User avatar
Dave999
Posts: 9624
Joined: Thu Feb 24, 05 10:31 am
Location: Twickenham,London, England

Re: Propshaft UJ replacement

Post by Dave999 »

did it vibrate before?
do you intend spinning it way faster than you currently do Overdrive Trans etc

if neither is the case you are paying for a balance job, for peace of mind
nice to know its right but not stricktly necessary if it all worked ok previously


David
The Greater Knapweed near the Mugwort by the Buckthorn tree is dying
User avatar
Steve
Posts: 7726
Joined: Wed Feb 01, 12 7:19 pm
Location: Scotland

Re: Propshaft UJ replacement

Post by Steve »

Dave, if I'm honest, I was hoping you would answer this for me.....brilliant as always :thumbright: :thumbright:

Everything is standard on my car and original. It has the original 383 4V HP engine so I understand was fitted with the larger UJs. I have two sets of new MOOG heavy duty ones that my pal from Canada brought over for me. I measured them as best I could and that backs up the large joint option on the car. I don't have any vibration at all but some play was picked up a few years ago on an MOT so I thought I would do them as I have them. I'm getting a small amount of whining from the rear (not the kids, I checked, they are still in Oz at the last count :argue: ). I checked the diff oil and it's topped up and a clean and clear as the day I put it in about 12 years ago and the wheel bearings are fine so am hoping the UJs may be a contributing factor. The noise sounds like tyre noise more than anything but it is a bit more than that in my mind.

I will take the prop shaft off and do the work on the bench. I don't have a lift so will use other means.

Thanks again Dave, really appreciate the benefit of your experience on this.... Cheers Steve :thumbright:
Bat Girl Stalker Living Petes Dream
User avatar
Dave999
Posts: 9624
Joined: Thu Feb 24, 05 10:31 am
Location: Twickenham,London, England

Re: Propshaft UJ replacement

Post by Dave999 »

no probs
had mine off and on numerouse times, its not hard but its a job where you find yourself saying "More haste less speed" when you relasie you forgot to put the c clips on or have not squished the cups into position well enough

if the cups fall off, the needle rollers in theory should not fall out, espceailly when new, a full compliment of barnd new rollers stays in of its own accord... reloading the things is again abit of a task ...

if it still whines a bit and you are sure its not the diff/ bearings or brakes has the rear end sagged just enough to create a minor pinion angle mismatch or has your rear trans mount slowly converted its rubber section into a soft cheese sponge over the years
if its ever got oily the rubber goes like a perished elastic band and the back end of the trans can move
just heave the transmisson about if the mount is squidgy you need a new one

this causes a pop pop pop in the joints as the shaft tries to go faster at one end than the other
The Greater Knapweed near the Mugwort by the Buckthorn tree is dying
User avatar
Steve
Posts: 7726
Joined: Wed Feb 01, 12 7:19 pm
Location: Scotland

Re: Propshaft UJ replacement

Post by Steve »

Cheers Dave. I would say my rear springs are 'tired' but I have air shocks on the back that compensate. I have a new trans mount so will probably replace that while I'm doing this job. Im assuming it's pretty easy to check the bearing in the diff just by turning the yoke and feeling for roughness or is it more complicated?? :read2:
Bat Girl Stalker Living Petes Dream
Post Reply